home


what is the Seven?


build diary
  1439 new entries

videos


parts sources
good links
parts list
cost breakdown


what book?
get your copy
other recommendations corrections



email


say hi!

build diary

<< | show individual entries | >>

December 13, 2004:
Better stripper.
I've been told via email and the guestbook that my paint stripper was not manly enough. The key is to use the semi-gelled type that paints on. The paint shop that recommended the spray-on stuff was wrong! Once again, after finding the pros didn't quite have what I needed I headed for Lowes. A bottle of Jasco stripper cost less than a single spray can and it definitely did the job. Combined with a solvent-proof brush from Walmart, a Scotch Brite pad and a not-solvent-proof scraper I was able to make a huge difference to the wheels. Tomorrow I'll see how they paint. Thanks to Richard and Jonathan for the tips.

I was busy over the weekend driving. I brought a video camera along and I've put some pretty fun videos together. Nothing fancy (yet), just some back road driving. This will give you a hint of the sort of roads that we have right on the edge of town. They sure look fast in the little versions, holy cow. Want to see them?
entry 721


December 14, 2004:
Not the biggest installation, but a Voodoo brake handle has replaced the plastic one.
Hey, it matches the car. My titanium shift knob also made it onto the car. Why? Because I like it.
entry 722
A future installation - this net from BMW.
It'll go on the passenger's side of the transmission tunnel to corral loose papers and sunglasses.
entry 723
The gelled stripper did the job.
A couple of drops of water mar the finish here, but you can see the difference from the earlier stuff. That's a clean wheel!
entry 724
More videos!
These are some fun ones to watch. Watch the videos here.
entry 725

December 15, 2004:
I'll be painting the wheels with Dupli-Color "High Performance Wheel Coating", whatever that is exactly.
It's available in clear, silver, graphite, bronze or satin black according to the website. Well, I decided to go with satin although it's hard to find. My local NAPA put in an order and bronze showed up. The part number was correct, the paint just wasn't right. So for fun, I had them ship two cans of "bronze". Guess what? It's black. Not satin but flat black. Since the clearcoat will add a bit of gloss I decided to go with this. It was a close call, I almost decided on graphite. Let's hope it turns out well. For the record, order part number HP104 for black and HP105 for bronze. First I have to polish the rims - and by that, I don't mean the entire wheel. I mean the actual rim of the wheel. The popular vernacular seems to have lost the distinction. But I digress. Some kerb marks need to be removed and then it's just a matter of making everything super-shiny. I'll put clearcoat over the polish too because I'm lazy. Thanks to Jonathan Adams for much advice on how to do this.
entry 726


December 16, 2004:
Well, the painting comment was premature.
I have to finish polishing the wheels first. Or would the more appropriate term be "start"? Anyhow, I'm going to put the Seven on a lift and use it as a 130 hp lathe to spin the wheels for me. That should help to get a nice even finish on the kerbed sections. I've tried hitting a test spot with a Scotch Brite doodad (looks like some sort of sphere made out of blocks, used for porting heads) on a die grinder and while that works a treat, it also has the effect of slightly flattening the area. Not a problem when it's painted but it will make the polished section look dented. Okay, they're not the best wheels to start with but there's no reason to exaggerate that. So I'll try a couple of other tacks. I just need 1) the enthusiasm and 2) access to the lift. This weekend.

While it's up in the air, I'm going to raise the ride height a bit. I forget that all of my "eyeballing" of ride height has been done with the car empty. With me in it, the rear is sinking by 1/2" or so. With two on board, it's worse. So I'll compensate for that. I'm also going to cornerweight the car and see if I can get it nicely balanced. The only question is - set it up for one or for two?
entry 727


December 17, 2004:
A bit of polishing tonight.
I put the Seven up on the lift and used it as a lathe. That works pretty well but it's hard to get right in to the corner by the spokes without your fingers going bonk bonk bonk. I don't have the perfect mirror finish yet - it's still more of a satin - but it's looking pretty nice. It's the shiniest thing on the car by far right now! I first hit the spinning wheel with the Scotch Brite bit on a Dremel to bring down the high points. I don't think I can dig it down to the point of removing all the marks but it looks much better. Maybe some coarse sandpaper? The bit was followed with a Scotch Brite pad and then polish, but this still left some "grain". I tried again with 2000 grit wet/dry sandpaper left over from when I finished the paint on the Cadillac then hit it with the Meguiars polish. Much better. I think I need one more intermediate step with something a little more aggressive than the Meguiars but even as it is it would look blinding in the sun.

I added a short short video clip of what it's like to pass on a country road. Pretty quick! The videos are now in a more Mac-friendly format, my apologies to those of you with OS X. This weekend is supposed to be nice, I'll head back out again with the camera.
entry 728

How do you polish wheel rims? With a 130 hp lathe of course!
entry 729
You can see the current finish on the rim along with the worst of the kerbing.
Ouch.
entry 730
Hey, Grassroots put a photo of their car in the magazine with tires that wouldn't clear the fenders.
So I'll go one bigger. Actually, several sizes bigger. That's a Goodyear 23x10 race slick. Nope, it's not even close. I'll need a spacer just to clear the spring.
entry 731

December 18, 2004:
There are so many things I should be doing instead of playing with my Seven.
But I'm not.

The wheels are polished. The solution to the nasty kerb scars was an 80 grit flapper wheel on a die grinder. Overkill perhaps, but it sure did the trick. This was followed with some 220 grit to clean things up, then some coarse and fine Scotch Brite wheels. A rub with a coarse Scotch Brite pad put a nice satin finish on things, then I wet-sanded with 600, 1000 and 2000 grit. Some rubbing compound (the missing link from yesterday), aluminum polish and a final shot with Nevr-Dull wadding and boom! A very shiny wheel. It turns out I started with the worst wheel of the lot. Two had no kerb marks at all and those cleaned up in about 30 minutes. I did all the work with the wheel spinning to avoid variations in the shape of the rim. With the polish, those would have been very obvious.

So after all the polishing, I cleaned everyhing up with brake cleaner, carefully masked the rims and started painting. Two coats of self-etching primer, two coats of the Dupli-Color and then a coat or two of clear. How will it look? Hard to say, I'm heading off to put the second coat of black on right now.

While waiting for paint to dry (how exciting!) I checked a few things on teh car. The connection between the upper control arm and the upright was backing out a bit, so I tightened that up after taking out a bit of camber. I also raised the ride height by about 1/2" to give me some more peace of mind. Just for fun I threw the car on the scales - the cross weights are 50.2/49.8 with me in the driver's seat. Not bad for an eyeball setting, really!
entry 732

The final polish result.
The wheel on the right hasn't been done yet, the wheel on the left is finished.
entry 733
A before and after.
Hmm, the "new" wheels look pretty good.
entry 734
The polished rim is masked off and the wheels are ready for paint.
entry 735
Warming the cans in hot water helps give a better quality coat.
As you can tell, I'm starting with some self-etching primer.
entry 736
Primed, ready for the black.
It's hard to tell what's fresh paint and what's primer!
entry 737

December 19, 2004:
I had to stop in to the garage this morning to see how the wheels look.
It took a fair bit of time last night to take off the masking tape (it wasn't easy to put on either!) and then give a final swipe at the wheels. But a couple of thin coats of clearcoat and now they're done! They look just like I expected which is almost a little disappointing. I expected some radical change but really, they're just black with polished rims. Okay, not a big surprise. I suspect that I would have been more impressed if I'd gone with graphite instead. I think this combination will look better on the Seven though. The finish looks good - I would have been a little upset if a new set of $300 SSR Competitions looked like this, but for a set of wheels that were all banged up and looked fairly crusty it's a major transformation. The biggest problem is the join between the paint and the polish. The line isn't quite razor sharp on about one spoke per wheel despite my care in masking. But I'm the only person who will ever know (well, I was...) because you have to be looking very closely. Overall it was time well spent and I think the car will really look good. It's one step further away from having a recongizable donor. Now all I have to do is order some tires.

One thing I noticed last night when flipping through an old issue of EVO - their R400 was orange with black front fenders and black wheels with polished lips. Sounds familiar although they did paint all the body. And that suspension lift last night seems to have made the car ride better although I'm not sure how much of that is psychological.
entry 738

A finished wheel out in the sun.
entry 739

December 22, 2004:
I'm heading out for the holidays.
I'm sure when I return in a couple of weeks that I'll be full of plans for the Seven. Maybe I'll even order some tires so I can put my "new" wheels on! It'll be quite different than my vacation last year - then I was all excited about the possibility of the frame arriving, now I'm all excited about upcoming track time. It's rather hard to believe.
entry 740


January 4, 2005:
Happy new year, everyone.
As a little present to the car, I ordered a set of Azenis tires for the Seven. As a little present to me, my parents bought me a helmet. No more loaners for me at the track!

I should have the opportunity to get some work done on the Seven this weekend. Plans are quite tentative at the moment as to exactly what will be happening, but I've been eyeing a set of individual throttle bodies that happen to be on the shelf at Flyin' Miata. Ooooh, the temptation. I should also really work on the wipers but the thought of drilling the holes in the scuttle makes me sad. I've also started researching trailers and trailer designs. Can I build a Seven trailer with electric brakes for a reasonable price? Let's see.

Oh, and a new project has arrived: a 1988 Mazda 323 GTX. It's a little AWD turbocharged hatchback that just happens to use the same 1.6 engine as my Miata and the Seven. I now have three very different cars in my garage that all run off the same powerplant. This will be fixed up to daily driver status.

A bit of Googling around the net has turned up a couple of interesting things. Apparently my build was being mentioned by the CMC folks a few months back - you can read about it in several Lotus club newsletters including page 4 of reMarque. I also found that rec.auto.makers.mazda.miata seems to have decided I did my best to build the ugliest car possible out of a Miata. A BMW rebody was viewed as a better choice. I think they got a misleading idea of the size of the car judging by their "expert" analysis. Ahh, nothing like the courage of anonymity. To each their own, I'll wave as I go by.
entry 741

<< | show individual entries | >>